Audio Speakers

Showing 13–24 of 32 results

Cube Audio Sub 10

SUB 10

The Cube Audio Sub 10 were designed to accompany the Nenuphar Mini Monitors, Nenuphar Mini, Magus or even Bliss C loudspeakers. Since we used sealed cabinets for very low group delay and amazing accuracy, the integration of the sub with full-range driver is very easy and effortless. The fullrange driver does not have any crossover so the sound is as pure as was before, just the lowest bass is added if necessary. Complete regulation of SUB volume, phase with an addition of 0 – 6 dB gain in the range of 30-50 Hz make the sub a perfect match for the speakers.

The woofer in the sub is very fast and relatively lightweight. That allows a AB Class 200W Amp to deliver very energetic, superbly controlled bass. The sub amp allows for volume, phase, frequency cut-off, boost regulation so it enables placing the speakers in the best sounding spot in your room and than just adjust the bass parameters to your liking. You will never have trouble with bass again.

The sub is offered as the NENUPHAR MINI BASiS set. It consist of two NENUPHAR MINI MONITORS and two SUB 10 units.

It can be also combined with any of our loudspeakers from classic Nenuphar to Bliss C. One or two units can be used for entire system. That way you can transform your current speakers into the beasts that will give you live concert experience at home.

Parameters:
Cabinet type: Sealed
Amp power: 200W AB Class
Woofer size: 10″
Resonant frequency: 20 Hz
Efficiency: 88 dB @ 1W
Frequency response: 20 Hz – 200Hz ( 3db)*
Dimensions: 40 x 50 x 25 cm
Weight: 20 Kg

* Frequency response may vary and depends on room size and accompanying electronic equipment.

Read more
Cube Audio Sub 12

SUB 12

The Cube Audio Sub 12 were designed to accompany the Nenuphar Monitors or classic Nenuphar so sealed cabinets are used for very low group delay and amazing accuracy. The integration of the sub with full-range driver is very easy and effortless. The fullrange driver does not have any crossover so the sound is as pure as was before, just the lowest bass is added if necessary. Complete regulation of SUB volume, phase with an addition of 0 – 6 dB gain in the range of 30-50 Hz make the sub a perfect match for the speakers.

The woofer in the sub is very fast and relatively lightweight. That allows a AB Class 200W Amp to deliver very energetic, superbly controlled bass. The sub amp allows for volume, phase, frequency cut-off, boost regulation so it enables placing the speakers in the best sounding spot in your room and than just adjust the bass parameters to your liking. You will never have trouble with bass again.

The sub is offered as a NENUPHAR BASiS set. It consist of two NENUPHAR MONITORS and two SUB12 units.

It can be also combined with any of our loudspeakers from classic Nenuphar to Bliss C. One or two units can be used for entire system. That way you can transform your current speakers into the beasts that will give you live concert experience at home.

Parameters:
Cabinet type: Sealed
Amp power: 200W AB Class
Woofer size: 12″
Resonant frequency: 19 Hz
Efficiency: 88 dB @1W
Frequency response: 18 Hz – 200Hz ( 3db)*
Dimensions: 30 x 50 x 105 cm
Weight: 23 Kg

* Frequency response may vary and depends on room size and accompanying electronic equipment.

Read more
Quested CX8 Speaker

Quested CX8 Speaker

QUESTED HIGH POWERED CEILING OVER HEAD SPEAKERS

When clarity, power and fatigue free sound is required. Quested CX8 passive designed speakers will deliver above your expectations. Small form factor designed speakers that can easily fit into the tightest spaces but delivery a large open sound, Suitable installs: High End Residential Cinemas & Media Rooms, Private Venues, Clubs, Bars, Restaurants, Hotels, Gyms, Offices etc.

Read more
Quested H108 Speakers

Quested H108 Speakers

The H108 is the smallest of the Quested passive monitors. Primarily designed to be used in a nearfield or a meter-bridge position. It utilises a single 8” custom LF driver and silk soft dome HF with front firing ports. The hand built crossover network offers a very efficient and transparent passive network. Delivering an exceptional and accurate sound stage along with the ability to produce a high SPL when required, the H108 has become a favourite with the mastering and broadcast community. The H108 is also the monitor that Roger uses at home.

TECHNICAL SPECIFICATION
Dimensions: 240(w) x 404(h) x 244(d) mm

Weight: 12 kg / 25.5 lb

Drivers: Bass cone – 1 x 200 mm (8 ”)

High Frequency: Soft dome – 1 x 28 mm (1 ⅛”)

Maximum SPL: 107 dB continuous pink noise @ 1m Leq 1 minute. 113 dB continuous pink noise per pair @ 1m Leq 1 minute

Frequency Response: 82 Hz-20 kHz ± 2 dB / 46 Hz-22 kHz -6 dB

Connector: Single pair binding posts

Impedance: 8 ohms

Sensitivity: 90.5 dB @ 1 m

Power Requirements: Amplifier rated at 8 ohms delivering between 60 and 200W RMS per channel

Read more
Quested HQ210 Speakers

Quested HQ210 Speakers

The largest of the three way passive monitors is the HQ210. With two 10” LF drivers along with a soft dome mid and a soft dome high mounted in a rotatable baffle, the HQ210 can be used vertically or horizontally. As with all the passive Quested monitors a hand built crossover network is employed that offers a very efficient and transparent performance. Designed to be a midfield main monitor for use as either a soffit or free standing system. The HQ210 is the most powerful passive monitor in the Quested range. Recommended partner amplifier is the Quested AP1550-2.

TECHNICAL SPECIFICATION
Dimensions: 590(w) x 850(h) x 355(d) mm

Weight: 60 kg / 132 lb

Drivers: Bass cone – 2 x 250 mm (10 ”)

Mid Frequency soft dome: 1 x 75 mm (3”)

High Frequency soft dome: 1 x 28 mm (1 ⅛”)

Maximum SPL: 113.5 dB continuous pink noise @ 1m Leq 1 minute. 119.5 dB continuous pink noise per pair @ 1m Leq 1 minute

Frequency Response: 40 Hz-20 kHz ± 2 dB / 35 Hz-22 kHz -6 dB

Connector: Triple pair binding posts

Impedance: 8 ohms

Sensitivity: 92dB @ 1 watt 1

Power Requirements: Amplifier rated at 8 ohms delivering between 300 and 900W RMS per channel

Read more
Quested QSB112 Subwoofer

Quested QSB112 Subwoofer

The QSB112 sub-woofer is the ideal solution for engineers and producers who require an accurate high power reference near to mid filed subwoofer. The custom designed 12” driver features an external radial chassis that provides greater cooling benefits to the voice coil and magnet assembly reducing thermal compression within the driver when operating at higher SPL’s. With a frequency response down to 25Hz the QSB112 is suitable for production work both with music and film in multi-channel systems and is the perfect partner to the VH3208. The recommended amplification option is the SBC800. The SBC800 includes all the tools necessary to align and configure your system with L/C/R and LFE inputs along with adjustable crossover, phase and gain. Two parametric EQ’s. Bypass and solo functions. The output stage of the SBC800 delivers 800W in to 4ohm and can drive up to two QSB112’s

The Quested QSB112 12″ Passive Subwoofer extends the low frequency response of the monitoring system. It’s the perfect addition to situations where extended or high levels of LF performance are required.

TECHNICAL SPECIFICATION:

• Dimensions: 485(w) x 700(h) x 324(d) mm
• Weight: 39 kg / 86 lb
• Drivers: Bass cone – 1 x 305 mm (12 ”)
• Max SPL: 121 dB continuous pink noise @ 1m Leq 1
minute. 127 dB per pair pink noise @ 1m Leq 1 minute
• Frequency Response: 29 Hz-200 Hz ± 2 dB &
25 Hz – 6 dB
• Impedance 8 ohms
• Sensitivity 92 dB @ 1W 1m
• Connector 4 pole Speakon
• Recommended amplifier SBC800

Read more
Quested QSB115 Subwoofer

Quested QSB115 Subwoofer

The QSB115 sub-woofer is the ideal solution for engineers and producers who require an accurate high power reference near to mid filed subwoofer. The custom designed 15” driver features an external radial chassis that provides greater cooling benefits to the voice coil and magnet assembly reducing thermal compression within the driver when operating at higher SPL’s. With a frequency response down to 25Hz the QSB115 is suitable for production work both with music and film in multi-channel systems.
The recommended amplification option is the SBC800. The SBC800 includes all the tool necessary to align and configure your system with L/C/R and LFE inputs along with adjustable crossover, phase and gain. Two parametric EQ’s. Bypass and solo functions. The output stage of the SBC800 delivers 800W in to 4ohm and can drive up to two QSB115’s

The Quested QSB115 15″ Passive Subwoofer extends the low frequency response of the monitoring system. It’s the perfect addition to situations where extended or high levels of LF performance are required.

TECHNICAL SPECIFICATION:

• Dimensions: 610(w) x 875(h) x 420(d) mm
• Weight: 48 kg / 106 lb
• Drivers: Bass cone – 1 x 305 mm (12 ”)
• Max SPL: 123.5 dB continuous pink noise @ 1m Leq 1minute.
129.5 dB per pair pink noise @ 1m Leq 1 minute
• Frequency Response: 26 Hz-200 Hz ± 2 dB & 25Hz-200Hz±6dB
• Impedance 8 ohms
• Sensitivity 93 dB @ 1W 1m
• Connector 4 pole Speakon
• Recommended amplifier SBC800

Read more
Quested S6R Speakers

Quested S6R Speakers

The S6R is the most compact unit in the ranger offering a 5” low frequency driver in an infinite baffle enclosure. The built in amplification provides a total of 110W RMS to the drivers. Power is split with 65W RMS to the 5” LF and 45W RMS to the silk dome tweeter. Attenuation to the input sensitivity along with low and high frequency is available on the rear panel. The frequency response is 80Hz – 20kHz with a +- 2db tolerance and a -6dB cut off at 67Hz. Ideally suited to those with limited space and when coupled to the SB10R offers a very powerful yet compact full range monitoring solution.

TECHNICAL SPECIFICATION
Dimensions: 170(w) x 285(h) x 240(d) mm

Weight: 7.5 kg / 15.5 lb

Drivers: Bass cone – 1 x 130 mm (5 ”)

High Frequency: Soft dome – 1 x 28 mm (1 ⅛”)

Maximum SPL: 100 dB continuous pink noise @ 1m. Leq, 1 minuet, single unit. 106 dB continuous pink noise @ 1m. Leq, 1 minuet per pair

Frequency Response: 80 Hz-20 kHz ± 2 dB / 67 Hz-22kHz -6 dB

Connector: XLR and ¼ inch Jack combo socket

Impedance: 10k electronically balanced with RF filters

Wiring:

Pin 1 ground Sleeve
Pin 2 hot Tip
Pin 3 cold Ring

Sensitivity: -12 dBu to +6 dBu for 96 dB SPL @ 1 m set by 10 position rotary switch on rear

Subsonic: -3dB @ 45 Hz, 24dB/oct

Ultrasonic: -3dB @ 75kHz, 4dB/oct

Crossover: 1k19

LF EQ: -2/- 4 @ 82 Hz

HF EQ: +/- 2dB @ 10 kHz

POWER AMPLIFIER
LF output power: 65W RMS continuous (note 1)

HF output power: 45W RMS continuous (note 1)

THD: 0.03% at levels up to 1 dB below clip, 20 Hz-20 kHz. Typ 0.005% @ 1kHz.

Hum & Noise: > -100 dB referred to clip

Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100 mm clearance) around the amplifier heatsinks and an ambient temperature not exceeding 30 Degrees C.

INDICATORS
Power on: Front mounted green LED indicates power applied.

Clip: Red LED 2 dB before amplifier clip.

POWER REQUIREMENTS
Voltage: Set by internal plugs: nominal 115V or 230V @ 50-60 Hz AC 230V setting: min 160V; restricted output power: max 255V 115V setting: min 80V; restricted output power: max 127V

CONSUMPTION
Quiescent: 12W

Typical use: 45W (average music)

Max: 90W (average music)

Note: 0 dBu = 775 mV into open circuit

This product is built to conform to the requirements for CE marking.

Read more
Quested S7R Speakers

Quested S7R Speakers

The S7R is designed to be compact yet offer a bass extension suitable for the majority of monitoring requirements. Incorporating a 6.5” low frequency driver with a double flared front loaded port design means reduced turbulence and a monitor that is very forgiving of placement to walls. The built in amplification provides a total of 190W RMS to the drivers. Power is split with 120W RMS to the 6.5” LF and 70W RMS to the silk dome tweeter. Attenuation to the input sensitivity along with low and high frequency is available on the rear panel. The frequency response is 68Hz – 20kHz with a +- 2db tolerance and a -6dB cut off down to 58Hz . The With the addition of the SB10R the frequency response can be taken down to 27Hz for those wanting to accurately monitor down to the lowest of usable acoustics frequencies.

TECHNICAL SPECIFICATION
Dimensions: 244(w) x 347(h) x 302(d) mm

Weight: 11.7 kg / 25.5 lb

Drivers: Bass cone – 1 x 165 mm (6 ½”)

High Frequency: Soft dome – 1 x 28 mm (1 ⅛”)

Maximum SPL: 105 dB continuous pink noise @ 1 m LEQ 1 minute. 111 dB per pair pink noise @ 1m Leq 1 minute

Frequency Response: 68 Hz-20 kHz ± 2 dB / 58 Hz-22kHz -6 dB

Connector: XLR and ¼ inch Jack combo socket

Impedance: 10k W electronically balanced with RF filters

Wiring:

Pin 1 ground Sleeve
Pin 2 hot Tip
Pin 3 cold Ring
Sensitivity: -12 dBu to +6 dBu for 96 dB SPL @ 1 m set by 10 position rotary switch on rear

Subsonic: -3dB @ 30 Hz, 24dB/oct

Ultrasonic: -3dB @ 75kHz, 4dB/oct

Crossover: 1k19

LF EQ: -2/-4 @ 65 Hz

HF EQ: +/- 2dB @ 10 kHz

POWER AMPLIFIER
LF output power: 120W RMS continuous (Note 1)

HF output power: 70W RMS continuous (Note 1)

THD: 0.03% at levels up to 1 dB below clip, 20 Hz-20 kHz. Typ 0.005% @ 1kHz.

Hum & Noise: -100 dB referred to clip

Note 1: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100 mm clearance) around the amplifier heatsinks and an ambient temperature not exceeding 30ºC.

INDICATORS
Power on: Front mounted green LED indicates power applied.

Clip: Red LED 2 dB before amplifier clip.

POWER REQUIREMENTS
Voltage: Set by internal plugs: nominal 115V or 230V @ 50-60 Hz AC 230V setting: min 160V; restricted output power: max 255 AC 115V setting: min 80V; restricted output power: max 127V

CONSUMPTION
Quiescent: 18W

Typical use: 75W (average music)

Max: 140W (average music)

Note: 0 dBu = 775 mV into open circuit

This product is built to conform to the requirements for CE marking.

Read more
Quested S8R Speakers

Quested S8R Speakers

The S8R is the largest of the S Series monitors. With an 8” low frequency transducer coupled to a double flared front loaded port design means reduced turbulence. This design also allows for easy placement of the S8R in compact spaces. The on board amplification delivers 370W RMS split with 220W RMS to the 8” LF and 150W RMS to the silk dome tweeter. Attenuation to the input sensitivity along with low and high frequency is available on the rear panel. The frequency response is 53Hz – 20kHz with a +- 2db tolerance and a -6dB cut off down to 41Hz. The S8R can also be partnered with the SB10R should further sub base extension be required down to 27 Hz.

TECHNICAL SPECIFICATION
Dimensions: 300(w) x 428(h) x 334(d) mm

Weight: 17.6 kg / 39lb

Drivers: Bass cone – 1 x 200 mm (8”)

High Frequency: Soft dome – 1 x 28 mm (1 ⅛”)

Maximum SPL: 106.5 dB continuous pink noise @ 1m LEQ 1 minute 113 dB per pair pink noise @ 1m Leq 1 minute

Frequency Response: 53 Hz-20 kHz ± 2 dB / 41 Hz-22kHz -6 dB

Connector: XLR and ¼ inch Jack combo socket

Impedance: 10k ohm electronically balanced with RF filters

Wiring:

Pin 1 ground Sleeve
Pin 2 hot Tip
Pin 3 cold Ring
Sensitivity: -12 dBu to +6 dBu for 96 dB SPL @ 1 m set by 10 position rotary switch on rear

Subsonic: -3dB @ 20 Hz, 24dB/oct

Ultrasonic: -3dB @ 75kHz, 4dB/oct

Crossover: 1k40

LF EQ: -2/- 4 @ 42 Hz

HF EQ: +/- 2dB @ 10 kHz

POWER AMPLIFIER
LF output power: 220W RMS continuous (Note 1)

HF output power: 150W RMS continuous (Note 1)

THD: 0.025% at levels up to 1 dB below clip, 20 Hz-20 kHz. typ 0.005%@ 1kHz.

Hum & Noise: -100 dB referred to clip

Note 1: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100 mm clearance) around the amplifier heatsinks and an ambient temperature not exceeding 30ºC.

INDICATORS
Amplifier Warming Up: Front mounted flashing green LED indicates that the amplifier is warming up to reach peak performance.

Normal Operation: Green LED indicates power applied and normal operation.

Clip: Red LED 2 dB before amplifier clip.

Fault Indication: Red constantly on indicates fault.

POWER REQUIREMENTS
Voltage: Set by internal plugs: nominal 115V or 230V @ 50-60 Hz AC 230V setting: min 160V; restricted output power: max 255 AC 115V setting: min 80V; restricted output power: max 127V

CONSUMPTION
Quiescent: 38W

Typical use: 100W (average music)

Max: 160W (average music)

Note: 0 dBu = 775 mV into open circuit

This product is built to conform to the requirements for CE marking.

Read more
Quested SB10R Subwoofer

Quested SB10R Subwoofer

THE PERFECT PARTNER FOR YOUR S-SERIES MONITORS
The SB10R is the reference subwoofer that partners with the S-Series. Delivering a powerful yet clean bass response all the way down the 25Hz, the SB10R completes the S-Series. A 10” driver is perfectly matched to the cabinet volume and paired with its own dedicated remote power amplifier. The SBC250 amplified controller (250W) has all the features to allow perfect integration of the sub with any system. It has a variable crossover from 40Hz to 135Hz, gain control from -14db to +6db, up to 160 degrees of phase control, along with a polarity ± switch, output level metering and a bypass function, all in a 1U rack unit. Remote power allows for very easy setup, with all the controls you need at your fingertips.

TECHNICAL SPECIFICATION
Dimensions: Cabinet 600(w) x 332 (h) x 300(d) mm SBC250 Controller – 1U case 270mm deep

Weight: Cabinet – 19.8 kg / 43.4 lb
SBC250 Controller – 5.5 kg / 12 lb

Drivers: Bass cone 1 x 250mm (10”)

Frequency Response: User Adjustable. 25 Hz-200 Hz ± 2 dB / 17 Hz-200 Hz -6 dB

Maximum SPL: 116 dB continuous pink noise @ 1m Leq 1 minute half space

Connector: 2 off XLR and ¼ inch jack combo socket

Impedance: 10k W electronically balanced with RF filters

Wiring:

Pin 1 ground Sleeve
Pin 2 hot Tip
Pin 3 cold Ring
OUTPUTS:

Left and Right Monitor 2 off XLR type male left & right outputs
Impedance 100 ohm electronically balanced
Wiring Pin 1 ground, Pin 2 hot, Pin 3 cold
Sub Bass Output: 1 pair binding posts

FILTERS: Left & Right Input Summed to Sub Output

Subsonic/High Pass: -3dB @ 14Hz, 24dB/oct or -3dB @ 28Hz, 24dB/oct (set by internal jumper)

Low Pass: -3dB @ 40Hz to 135Hz, externally adjustable @ 24db/oct or full range on CH A

Left & Right Input to Left & Right Output

Ultrasonic: -1dB @ 100k

High Pass: -3dB @ 40Hz to 135Hz, externally adjustable @ 24db/oct or full range on CH A

POWER AMPLIFIER
THD:

210W rms continuous
0.03% at levels up to 1dB below clip, 20Hz – 120Hz typ
0.005% @ 20W rms 100Hz

Hum & Noise: -100 dB referred to clip

POWER REQUIREMENTS:
Set by internal plug: normal 115V or 230V setting: Min 160V (restricted output power): Max 255V 115V setting: Min 80V (restricted output power): Max 127V

CONSUMPTION
Quiescent: <30Wv

Typical use: 50W

Max: <200W

Note: 0 dBu = 775 mV into open circuit

This product is built to conform to the requirements for CE marking.

CONTROLS
Crossover Frequency 40 – 135Hz, front panel pot
Test (Band limited pink noise), front panel recessed switch (LED indicates when on)
Sub bass bypass, front panel switch (LED indicates when bypassed)
Sub Gain –14 to +6, front panel pot (Sub level indicated with LED Meter)
Sub Phase, front panel pot
Sub Polarity, front panel recessed switch (LED indication for positive and negative polarity)
Power, front panel switch
Left channel sub filter bypass, rear mounted recessed Switch
Subsonic filter 14 or 28Hz, Internal jumpers

Read more
Quested V2104 Speakers

Quested V2104 Speakers

The V2104 is the latest model in Quested’s V-Series range of active, powered, monitors. The compact, ported, direct radiator design utilises a 4”/100mm paper cone bass driver and a 28mm /1 1/8th” soft-dome high frequency unit. Power is derived from a 2-channel class D module, chosen primarily for its sonic performance and also for its compact dimensions keeping the cabinet size to an absolute minimum. The diminutive size of the V2104 makes it the perfect choice for a portable monitor with the special edition MiniRedz version including a shoulder carry case. Low frequency performance can be seamlessly extended by using either our SB10 or QSB112 sub-woofers depending on speaker configuration, stereo, 5.1 etc. The self-powered model will be joined shortly by a remote-powered version with rack mountable amplifiers, perfect for use in locations such as a remote broadcast trucks. Performance will be maintained with up to 50 meter speaker cables. Ceiling and wall mounts are currently available, a floor stand will follow as will a smaller dedicated sub-woofer, the SB8.

TECHNICAL SPECIFICATION
Dimensions: 132(w) x 262(h) x 160(d) mm / 5.1″(w) x 10.3″(h) x 6.2″(d)

Weight: 3.5kg / 7.7lb

Drivers: Low Frequency 1 x 100mm(4″) LF

High Frequency: soft dome – 1 x 28mm (1. 1/8″)

Maximum SPL: 100 dB continuous pink noise @ 1m Leq 1 minute. 106 dB per pair continuous pink noise @ 1m Leq 1 minute

Frequency Response: 100 Hz – 19 kHz ± 2dB / 88 Hz -6 dB

INPUT
Connector: XLR and ¼ inch Jack combo socket

Impedance: 10k ohm Electronically balanced

Wiring: Pin 1 ground, Pin 2 hot, Pin 3 cold

Sensitivity: TBC

FILTERS
Protective lower filter : -3dB @ 45Hz, 24dB/oct

Protective upper filter : -3dB @30kHz, 24dB/oct

Crossover Point: 1k67H

POWER AMPLIFIERS
HF output power: > 70W rms continuous (Note 1)

LF output power: > 70W rms continuous (Note 1)

THD: Typ 0.01% @ 1kHz

Note 1: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (>100mm clearance) around the amplifier rear panel and ambient temperatures is <30 Degrees C

INDICATION
Power on: Front mounted switch with ring mounted LED .

Blue LED indicates power, Red LED 2 dB before amplifier clip.

POWER REQUIREMENTS
Voltage: Set by internal plugs: nominal 115V or 230V @ 45-63Hz AC.

230V setting: Min 180V (restricted output power): Max 264V

115V setting: Min 90V (restricted output power): Max 132V

CONSUMPTION
Quiescent : TBC.

Typical use : TBC

Max : 10W at 230 Vac

This product is built to conform to the requirements for CE marking.

Read more